ALLIANCE HA050L User Manual download pdf (Page 11)

70381601

Tumble Dryer Operation

Start Up

When power is applied to the tumble dryer, the control

will display its software version as “SXXX” (“XXX” is

the version number) for two seconds. If the control

was not powered down during a running cycle, it will

enter the Ready Mode.

Ready Mode

Figure 2

In Ready Mode, the default cycle LED is lit, and the

full vend price is displayed as left justified.

NOTE: For software versions less than “S003,” the

default cycle is LOW TEMP. For software version

“S003” or higher, the default cycle is MED TEMP.

The user may select a different cycle, if desired. (In

card reader machines, if the selected cycle has a vend

price which differs from the default cycle, the display

will be updated to show the new price.) If another

cycle is selected, the control will flash the amount

needed to satisfy the vend shown on the display. If the

vend price is not satisfied within one minute, the

tumble dryer control will stop flashing the vend price

and return to the Ready Mode. The display will

continue to show the remaining vend needed to start a

cycle.

Vends may be satisfied by a coin drop, start pulses, or

by a third party card reader. If a coin drop is used, the

remaining vend price will decrease with each coin

entry. If start pulses are used, the remaining vend price

will decrease with each received pulse. Once the vend

is satisfied, the START LED will begin to flash and

signal will sound for ten seconds. If a third party card

reader is used, the START LED will begin to flash

when a valid cash card is entered into the reader.

When the START keypad is pressed, the tumble dryer

will start. The START LED will stop flashing and

either the DRYING LED or the COOL DOWN LED

will be lit. The display will change to show the

remaining cycle time on the right side of the display.

The DRYING LED will be lit during the heat portion

of a heat cycle. The COOL DOWN LED will be lit

during the cool down portion of a heat cycle and

during an entire no heat cycle.

When a cycle is complete, the Four-Digit Display will

show “00” until the door is opened, a key is pressed, a

coin or card is entered, or a start pulse is received.

When the door is opened, the Four-Digit Display will

revert back to the Ready Mode.

Entering Coins

Coins are entered to satisfy the programmed vend

price for a selected cycle. Coins may be entered before

selecting a cycle or during an active cycle. When coins

are entered during an active cycle, the time remaining

is increased by the amount programmed by the owner

(refer to Programming MDC).

The owner may choose to add additional time for each

coin entered. If coins are entered for an active cycle

currently in the COOL DOWN Mode, coins entered

may push the cycle back into the DRYING Mode. The

maximum time for any cycle is 99 minutes.

Entering Cards

A card is entered to satisfy the programmed vend price

for a selected cycle. The card may be entered before

selecting a cycle or during an active cycle. When the

card is entered during an active cycle and the START

keypad is pressed, the time remaining is increased by

the amount programmed by the owner. Refer to

Programming MDC section.

The owner may choose to add additional time by

deducting a vend from the card or may require an

additional full vend price be deducted from the card. If

vend is deducted during an active heated cycle that is

currently in the COOL DOWN Mode, the additional

time added may put the cycle back into the DRYING

Mode. The maximum time for any cycle is 99 minutes.

Additional time cannot be added if it exceeds the

99 minute limit on a drying cycle.

DRY544R

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Comments to this Manuals

No comments

ALLIANCE HA050L User Manual Page 11

Comments to this Manuals

Related products and manuals for Electric laundry dryers ALLIANCE HA050L