ALLIANCE AE7133 Service Manual Page 34
- Page / 125
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
60549 33
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
NOTE: The holding and booster coil, and the
secondary coil can be replaced individually.
b. Burner Tube, Igniter and Bracket
NOTE: Burner tube and igniter can be removed
without removing gas valve and bracket.
(1) Remove one screw from right side of
burner housing holding burner tube in
place. Refer to Figure 14.
(2) Gently move burner tube toward rear of
dryer to disengage tab from slot on left side
of burner housing. Refer to Figure 18.
(3) Carefully rotate burner tube and igniter
counterclockwise so tab is at 8 o’clock
position.
(4) Move air shutter end of burner tube slightly
to right and CAREFULLY remove burner
tube and igniter assembly out through front
of dryer.
(5) Remove screw holding the igniter and
bracket to the burner tube and remove
igniter and bracket. Refer to Figure 17.
IMPORTANT: Use care in removal so as not to
damage or break igniter as it is very fragile.
IMPORTANT: Handle igniter by grasping the
white ceramic portion or bracket only. DO NOT
handle silicon carbide portion of igniter with hands
or allow any oil, grease or other foreign material to
contaminate it. Oil, grease and other impurities or
hairline cracks will cause the igniter to burn out.
c. Sensor
(1) Remove two screws from the bottom edge
of the front panel. Refer to Figure 12.
(2) Swing the bottom of the panel away from
the dryer to disengage hold-down clips and
guide lugs from cabinet top. Refer to
Figure 12.
(3) Disconnect wires from door switch. Refer
to Figure 13.
NOTE: Refer to the appropriate wiring diagram
when rewiring the switch.
(4) Remove wires from sensor terminals. Refer
to Figure 18.
(5) Remove screw holding sensor to burner
housing. Refer to Figure 18.
Figure 17
DRY952S
CARBORANDUM
IGNITER AND
BRACKET
ATTACHING
SCREW
ATTACHING
SCREW
IGNITER AND
BRACKET
NORTON
IGNITER AND
BRACKET
To Test Igniter
(Gas Models)
1. Disconnect igniter wires at disconnect block.
Refer to Figure 47.
2. Set test meter to read OHMS and put meter
probes on terminals of igniter wires.
3. Meter should register an Ohm reading of at least
40 Ohms. If meter does not register any Ohms or
less than 40 Ohms, replace the igniter.
IMPORTANT: Always examine all wires,
terminals and connectors to be sure wiring is
proper before replacing any components.
NOTE: Test procedure can be performed on
workbench if gas valve, igniter, burner tube and
burner housing have been removed from dryer.
- Home Laundry 1
- Table of Contents 2
- Section 1 4
- Safety Information 4
- Section 1 Safety Information 5
- Section 2 6
- Introduction 6
- Model Identification 7
- How Your Dryer Works 8
- Section 2 Introduction 9
- Section 3 10
- Troubleshooting 10
- 10 60549 11
- POSSIBLE CAUSE TO CORRECT 11
- 12 60549 13
- 14 60549 15
- 16 60549 17
- Section 4 18
- Grounding 18
- 18 60549 19
- Figure 3 19
- Figure 4 20
- 20 60549 21
- Figure 5 21
- Figure 6 21
- DRY1071S 22
- DRY1794S 23
- DRY1795S 23
- DRY1075S 24
- DRY1796S 24
- Section 5 Service Procedures 25
- DRY1055S 27
- Figure 11 28
- 28 60549 29
- Figure 12 29
- Figure 13 29
- 30 60549 31
- Figure 14 31
- Wiring Schematic 32
- 32 60549 33
- Figure 16 33
- Figure 17 34
- 34 60549 35
- Figure 18 35
- DRY1797S 37
- DRY855S 37
- Figure 20 38
- 38 60549 39
- Figure 21 39
- Figure 22 40
- Figure 23 40
- 40 60549 41
- Figure 24 41
- Figure 25 42
- 42 60549 43
- Figure 26 43
- Figure 27 44
- Figure 28 44
- 44 60549 45
- Figure 29 45
- Figure 30 45
- Figure 31 46
- 46 60549 47
- Figure 32 47
- 48 60549 49
- Figure 33 49
- Figure 34 50
- 50 60549 51
- Figure 35 51
- Figure 36 52
- 52 60549 53
- 54 60549 55
- Section 6 56
- Adjustments 56
- 56 60549 57
- Figure 38 57
- Section 7 58
- Figure 40 59
- 58 60549 59
- 1 - 3 60
- 60 60549 61
- Figure 43 61
- Figure 44 61
- Figure 45 62
- Burner Orifice SpudVent Screw 62
- Figure 48 64
- Figure 49 64
- 64 60549 65
- Figure 50 65
- MEMORY RECALL 66
- ON / SELECT STATUS 67
- AUTOMATIC 67
- TIME DRY 67
- 60549 67 68
- 68 60549 69
- AUTOMATIC CYCLES 69
- Figure 51 69
- Figure 52 70
- 70 60549 71
- Figure 53 71
- 60549 71 72
- 72 60549 73
- Figure 54 73
- Figure 55 74
- 74 60549 75
- Figure 56 76
- 76 60549 77
- Figure 57 77
- Figure 58 77
- 60549 77 78
- DRY1068S 79
- Figure 60 80
- Figure 61 90
- 90 60549 91
- Section 9 92
- 92 60549 93
- Section 10 94
- Wiring Diagrams 94
- 94 60549 95
- 96 60549 97
- MODELS NG7519 AND NG7319 98
- 98 60549 99
- MODELS NE7513 AND NE7313 99
- Through Serial No. S6271975XG 100
- 100 60549 101
- 102 60549 103
- MODELS NG6519 AND NG6319 104
- 104 60549 105
- MODELS NE6513 AND NE6313 106
- 106 60549 107
- MODEL NE6513 AND NE6313 107
- MODELS NG4519 AND NG4319 108
- Through Serial No. S6242593XD 108
- 108 60549 109
- Section 10 Wiring Diagrams 110
- 110 60549 111
- MODEL VE5013 111
- MODEL NG4719 AND NG4619 112
- 112 60549 113
- MODEL NE4713 AND NE4613 114
- 114 60549 115
- MODEL NE4513 AND NE4313 116
- 116 60549 117
- 118 60549 119
- 120 60549 121
- MODELS NG2119 122
- 122 60549 123
- MODELS NE2113 123
- 124 60549 125
Related products and manuals for Electric laundry dryers ALLIANCE AE7133
(28 pages)
(172 pages)© 2020, manymanuals.com. All rights reserved. | 0.982 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals