ALLIANCE AE7133 Service Manual Page 46
- Page / 125
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
60549 45
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
IMPORTANT: The seal can be adhered to the
bulkhead using 3M-1300 Sealant (obtain locally).
This is accomplished by applying a bead of 3M-1300
Sealant around the entire flanged area where the
felt seal contacts the bulkhead. Strap must be
installed with cupped surface down against the seal
to hold the felt seal more firmly in place on the
bulkhead. Seal must be held securely under strap
and folded under flanged edge around entire
bulkhead.
52. CYLINDER BELT
a. Remove two screws from the bottom edge of
the front panel. Refer to Figure 12.
b. Swing the bottom of the panel away from the
dryer to disengage hold-down clips and guide
lugs from cabinet top. Refer to Figure 12.
c. Disconnect wires from door switch. Refer to
Figure 13.
NOTE: Refer to the appropriate wiring diagram
when rewiring the switch.
d. Disengage belt from motor and idler pulleys,
Figure 24.
e. If present, disconnect cylinder light wires.
f. Remove four screws holding bulkhead to front
flange of cabinet. Lift complete bulkhead
assembly out of slots in cabinet. Refer to
Figure 30.
IMPORTANT: During reinstallation of front
bulkhead, be sure that air duct is properly
positioned with the flange inside of the felt seal on
the exhaust fan cover.
g. While supporting cylinder, carefully remove
belt off cylinder.
NOTE: When installing belt, be sure belt is
properly installed on motor and idler pulleys, and is
on the correct side of the idler lever. Refer to
Figure 24. Belt must be positioned around cylinder
between center and rear baffle screws with the
ribbed surface against the cylinder. After installing
belt, rotate cylinder manually to check that belt is
properly aligned.
53. CYLINDER ASSEMBLY
a. Remove two screws from the bottom edge of
the front panel. Refer to Figure 12.
b. Swing the bottom of the panel away from the
dryer to disengage hold-down clips and guide
lugs from cabinet top. Refer to Figure 12.
c. Disconnect wires from door switch. Refer to
Figure 13.
NOTE: Refer to the appropriate wiring diagram
when rewiring the switch.
d. Disengage belt from motor and idler pulleys.
Refer to Figure 24.
Figure 31
DRY861S
CYLINDER GLIDE
ATTACHING SCREWS
SPRING
SEAL MUST BE
POSITIONED UNDER
FLANGED EDGE
FELT
SEAL
SEAL
STRAP
(Installed
with
cupped
surface
against
seal)
BULKHEAD
- Home Laundry 1
- Table of Contents 2
- Section 1 4
- Safety Information 4
- Section 1 Safety Information 5
- Section 2 6
- Introduction 6
- Model Identification 7
- How Your Dryer Works 8
- Section 2 Introduction 9
- Section 3 10
- Troubleshooting 10
- 10 60549 11
- POSSIBLE CAUSE TO CORRECT 11
- 12 60549 13
- 14 60549 15
- 16 60549 17
- Section 4 18
- Grounding 18
- 18 60549 19
- Figure 3 19
- Figure 4 20
- 20 60549 21
- Figure 5 21
- Figure 6 21
- DRY1071S 22
- DRY1794S 23
- DRY1795S 23
- DRY1075S 24
- DRY1796S 24
- Section 5 Service Procedures 25
- DRY1055S 27
- Figure 11 28
- 28 60549 29
- Figure 12 29
- Figure 13 29
- 30 60549 31
- Figure 14 31
- Wiring Schematic 32
- 32 60549 33
- Figure 16 33
- Figure 17 34
- 34 60549 35
- Figure 18 35
- DRY1797S 37
- DRY855S 37
- Figure 20 38
- 38 60549 39
- Figure 21 39
- Figure 22 40
- Figure 23 40
- 40 60549 41
- Figure 24 41
- Figure 25 42
- 42 60549 43
- Figure 26 43
- Figure 27 44
- Figure 28 44
- 44 60549 45
- Figure 29 45
- Figure 30 45
- Figure 31 46
- 46 60549 47
- Figure 32 47
- 48 60549 49
- Figure 33 49
- Figure 34 50
- 50 60549 51
- Figure 35 51
- Figure 36 52
- 52 60549 53
- 54 60549 55
- Section 6 56
- Adjustments 56
- 56 60549 57
- Figure 38 57
- Section 7 58
- Figure 40 59
- 58 60549 59
- 1 - 3 60
- 60 60549 61
- Figure 43 61
- Figure 44 61
- Figure 45 62
- Burner Orifice SpudVent Screw 62
- Figure 48 64
- Figure 49 64
- 64 60549 65
- Figure 50 65
- MEMORY RECALL 66
- ON / SELECT STATUS 67
- AUTOMATIC 67
- TIME DRY 67
- 60549 67 68
- 68 60549 69
- AUTOMATIC CYCLES 69
- Figure 51 69
- Figure 52 70
- 70 60549 71
- Figure 53 71
- 60549 71 72
- 72 60549 73
- Figure 54 73
- Figure 55 74
- 74 60549 75
- Figure 56 76
- 76 60549 77
- Figure 57 77
- Figure 58 77
- 60549 77 78
- DRY1068S 79
- Figure 60 80
- Figure 61 90
- 90 60549 91
- Section 9 92
- 92 60549 93
- Section 10 94
- Wiring Diagrams 94
- 94 60549 95
- 96 60549 97
- MODELS NG7519 AND NG7319 98
- 98 60549 99
- MODELS NE7513 AND NE7313 99
- Through Serial No. S6271975XG 100
- 100 60549 101
- 102 60549 103
- MODELS NG6519 AND NG6319 104
- 104 60549 105
- MODELS NE6513 AND NE6313 106
- 106 60549 107
- MODEL NE6513 AND NE6313 107
- MODELS NG4519 AND NG4319 108
- Through Serial No. S6242593XD 108
- 108 60549 109
- Section 10 Wiring Diagrams 110
- 110 60549 111
- MODEL VE5013 111
- MODEL NG4719 AND NG4619 112
- 112 60549 113
- MODEL NE4713 AND NE4613 114
- 114 60549 115
- MODEL NE4513 AND NE4313 116
- 116 60549 117
- 118 60549 119
- 120 60549 121
- MODELS NG2119 122
- 122 60549 123
- MODELS NE2113 123
- 124 60549 125
Related products and manuals for Electric laundry dryers ALLIANCE AE7133
(28 pages)
(172 pages)© 2020, manymanuals.com. All rights reserved. | 1.723 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals