ALLIANCE JT37CGI Service Manual Page 66
- Page / 101
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
68 M411429
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
82. MAIN COIL
(Instant Electronic Ignition Models)
NOTE: The redundant coil cannot be purchased
separately. Replace complete gas valve.
a. Remove control panel.
b. Close gas shut-off valve. Refer to Figure 14.
c. Disconnect wires from main coil terminals.
d. Remove screws holding main coil to gas valve.
Refer to Figure 13.
83. BURNER TUBE
Refer to Figure 14.
a. Remove control panel.
b. Close gas shut-off valve.
c. Disconnect union nut attaching nipple to
spudholder and remove spudholder.
d. Remove screws holding gas valve bracket to
stove assembly.
e. Remove screws holding burner tubes to stove
frame and remove burner tubes.
IMPORTANT: Make sure that spudholder and
orifices are positioned such that gas will be injected
directly down the center of the burner.
84. CONTACTORS AND TERMINAL BLOCK
(Electric Models)
NOTE: Contactors and terminal blocks are located
in contactor box at the rear of the tumbler.
a. Remove screw holding cover to contactor box
and remove cover.
b. Remove wires from contactor terminals and
terminal blocks.
NOTE: Refer to wiring diagram when rewiring
contactors or terminal blocks.
c. Remove screws holding contactor to box.
d. Remove two screws holding terminal block to
box. Refer to Figure 15.
NOTE: OLDER MODELS - Terminal block
consists of two terminal section (one phase) or three
terminal sections (three phase) and an end piece
snapped together.
NEWER MODELS - Use a 3 pole terminal block.
To reduce risk of fire or explosion, check
pipe connections for gas leaks with a non-
corrosive leak detection fluid. Do not use an
open flame to check for gas leaks!
W310
WARNING
To reduce risk of fire or explosion, check
pipe connections for gas leaks with a non-
corrosive leak detection fluid. Do not use an
open flame to check for gas leaks!
W310
WARNING
Figure 15
T022SE1A
ATTACHING
SCREWS
CONTACTOR
CONTACTOR
TERMINAL
BLOCK
- Drying Tumblers 1
- Table of Contents 2
- Section 4 –Grounding 3
- Section 5 –Service Procedures 3
- Section 6 –Adjustments 3
- Section 1 4
- Safety Information 4
- 4 M411429 5
- Section 2 6
- Introduction 6
- Customer Service 7
- Serial Plate Location 7
- Safety Warnings and Decals 8
- How A Tumbler Works 9
- Energy Saver Models 10
- Section 3 11
- Troubleshooting 11
- 12 M411429 12
- POSSIBLE CAUSE TO CORRECT 12
- 14 M411429 14
- 16 M411429 16
- 18 M411429 18
- 20 M411429 20
- 22 M411429 22
- Section 3 Troubleshooting 23
- 24 M411429 24
- 26 M411429 26
- 28 M411429 28
- Section 4 50
- Grounding 50
- Section 5 51
- Service Procedures 51
- 54 M411429 52
- Figure 1 52
- Figure 2 53
- 56 M411429 54
- Figure 3 54
- MANUAL TIMER 54
- Figure 4 55
- Figure 5 55
- 58 M411429 56
- Figure 6 56
- Figure 7 56
- Figure 8 57
- Figure 9 57
- 60 M411429 58
- Figure 10 58
- Figure 11 59
- 62 M411429 60
- Figure 12 60
- Figure 13 61
- 64 M411429 62
- Figure 14 63
- 66 M411429 64
- Section 5 Service Procedures 65
- 68 M411429 66
- Figure 15 66
- Figure 16 67
- ELECTRIC HEATER 67
- 70 M411429 68
- Figure 17 68
- Figure 18 69
- 72 M411429 70
- Figure 19 70
- Figure 20 70
- Figure 21 71
- ALTERNATE STYLEREGULAR STYLE 71
- 74 M411429 72
- Figure 22 72
- Figure 23 72
- NEWER MODELS OLDER MODELS 73
- 76 M411429 74
- Figure 25 74
- Figure 26 74
- Figure 27 75
- NEWER MODELS 76
- Figure 29 77
- 80 M411429 78
- Figure 30 78
- BELT/CHAIN NONREVERSING 78
- 82 M411429 80
- Figure 31 80
- Figure 32 81
- Figure 33 81
- 84 M411429 82
- Figure 34 82
- Figure 35 83
- 86 M411429 84
- Figure 36 84
- Figure 37 85
- 88 M411429 86
- Figure 38 87
- 90 M411429 88
- Figure 39 89
- REVERSING CONTROL ASSEMBLY 89
- Adjustments 90
- Section 6 90
- INSUFFICIENT 91
- NO AIRFLOW 91
- Section 6 Adjustments 92
- 96 M411429 93
- Figure 42 93
- Figure 43 94
- Figure 44 94
- 98 M411429 95
- BELT DRIVE 96
- BELT/BELT REVERSING 97
- REVERSING 99
- Figure 48 100
- BELT/CHAIN 101
- NONREVERSING 101
Related products and manuals for Electric laundry dryers ALLIANCE JT37CGI
(61 pages)
(172 pages)
(473 pages)
(44 pages)
(97 pages)© 2020, manymanuals.com. All rights reserved. | 1.422 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals