ALLIANCE JT37CGI Service Manual Page 77
- Page / 101
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
M411429 79
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
100. DRIVE CHAIN
Nonreversing Tumblers
a. Remove drive guard.
b. Loosen jamnut on idler sprocket locking bolt
and move sprocket to the right to relieve chain
tension. Refer to Figure 30.
c. Run chain off drive sprocket and lift chain off
cylinder sprocket.
d. Reinstall chain and drive guard.
Reversing Tumblers
a. Repeat steps “a” and “b” of procedure for non-
reversing tumblers, above.
b. Loosen nut on idler housing attaching bolt and
slide idler housing to top of slotted mounting
holes in guide rails. Refer to Figure 31. This
will provide slack in drive chain for removal
from sprockets.
c. Adjust chain following installation. Refer to
Adjustments section.
101. IDLER HOUSING ASSEMBLY
Reversing Tumblers
a. Support drive guard and remove the screws
holding it to the back panel of the tumbler.
Leave the belt guard attached to the top of the
drive guard.
b. Loosen four capscrews holding motor
mounting bracket to side brackets. Lower
motor and mounting bracket until holding
capscrews bottom in the mounting slots.
c. Slip drive belt off of the motor pulley.
d. Loosen nut on idler housing attaching bolt and
slide idler housing to top of slotted mounting
holes in guide rails. Refer to Figure 31. This
will provide slack in drive chain for removal
from sprockets.
e. Remove top bolt from guide rail and remove
guilde rail, idler housing and sheave assembly.
f. After repairing or replacing idler housing
assembly, reinstall chain, belt, chain guard and
belt guard.
Figure 29
SCREWS
(Newer Models)
CLIPS
(Older Models)
BELT
GUARD
TU039-SV
- Drying Tumblers 1
- Table of Contents 2
- Section 4 –Grounding 3
- Section 5 –Service Procedures 3
- Section 6 –Adjustments 3
- Section 1 4
- Safety Information 4
- 4 M411429 5
- Section 2 6
- Introduction 6
- Customer Service 7
- Serial Plate Location 7
- Safety Warnings and Decals 8
- How A Tumbler Works 9
- Energy Saver Models 10
- Section 3 11
- Troubleshooting 11
- 12 M411429 12
- POSSIBLE CAUSE TO CORRECT 12
- 14 M411429 14
- 16 M411429 16
- 18 M411429 18
- 20 M411429 20
- 22 M411429 22
- Section 3 Troubleshooting 23
- 24 M411429 24
- 26 M411429 26
- 28 M411429 28
- Section 4 50
- Grounding 50
- Section 5 51
- Service Procedures 51
- 54 M411429 52
- Figure 1 52
- Figure 2 53
- 56 M411429 54
- Figure 3 54
- MANUAL TIMER 54
- Figure 4 55
- Figure 5 55
- 58 M411429 56
- Figure 6 56
- Figure 7 56
- Figure 8 57
- Figure 9 57
- 60 M411429 58
- Figure 10 58
- Figure 11 59
- 62 M411429 60
- Figure 12 60
- Figure 13 61
- 64 M411429 62
- Figure 14 63
- 66 M411429 64
- Section 5 Service Procedures 65
- 68 M411429 66
- Figure 15 66
- Figure 16 67
- ELECTRIC HEATER 67
- 70 M411429 68
- Figure 17 68
- Figure 18 69
- 72 M411429 70
- Figure 19 70
- Figure 20 70
- Figure 21 71
- ALTERNATE STYLEREGULAR STYLE 71
- 74 M411429 72
- Figure 22 72
- Figure 23 72
- NEWER MODELS OLDER MODELS 73
- 76 M411429 74
- Figure 25 74
- Figure 26 74
- Figure 27 75
- NEWER MODELS 76
- Figure 29 77
- 80 M411429 78
- Figure 30 78
- BELT/CHAIN NONREVERSING 78
- 82 M411429 80
- Figure 31 80
- Figure 32 81
- Figure 33 81
- 84 M411429 82
- Figure 34 82
- Figure 35 83
- 86 M411429 84
- Figure 36 84
- Figure 37 85
- 88 M411429 86
- Figure 38 87
- 90 M411429 88
- Figure 39 89
- REVERSING CONTROL ASSEMBLY 89
- Adjustments 90
- Section 6 90
- INSUFFICIENT 91
- NO AIRFLOW 91
- Section 6 Adjustments 92
- 96 M411429 93
- Figure 42 93
- Figure 43 94
- Figure 44 94
- 98 M411429 95
- BELT DRIVE 96
- BELT/BELT REVERSING 97
- REVERSING 99
- Figure 48 100
- BELT/CHAIN 101
- NONREVERSING 101
Related products and manuals for Electric laundry dryers ALLIANCE JT37CGI
(61 pages)
(172 pages)
(473 pages)
(44 pages)
(97 pages)© 2020, manymanuals.com. All rights reserved. | 2.414 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals