ALLIANCE JT37CGI Service Manual Page 45
- Page / 101
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
M411429 45
Section 3 Troubleshooting
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49. CD MODELS: NO START WITH VEND SATISFIED AND START BUTTON PRESSED IN
208-240 Volt/60 Hertz/3 Phase Gas Nonreversing
NOTE: All voltage checks are referenced to neutral unless stated otherwise.
Step Problem If No, then
1 Is there voltage to COM terminal of switch A?
If yes, continue to next step.
Correct wiring between L1 and switch A.
2 Is there voltage to the NC terminal of switch A?
If yes, continue to next step.
Check for proper operation of switch A. Replace switch
A if necessary.
3 Is there voltage to the common terminal of the door switch?
If yes, continue to next step.
Correct wiring between door switch and switch A.
4 With the door closed, is there voltage to the N.O. terminal
of the door switch? If yes, continue to next step.
Check door switch for proper operation, replace if
necessary.
5 Is there voltage to the input side of the Push-To-Start
button? If yes, continue to next step.
Correct wiring between start switch and door switch.
6 Is there voltage to the input side of the auxiliary contacts on
the motor contactor? If yes, continue to next step.
Correct wiring between motor contactor and door switch.
7 Is there voltage across the coil of the motor control
contactor?
Correct wiring between motor contactor and Push-To-
Start button.
8 If the start button is released, does the motor contactor stay
in the made position? If yes, continue to next step.
Check for proper operation of motor contactor, replace if
necessary.
9 Is there voltage to L1, L2, and L3 of the motor contactor?
If yes, continue to next step.
Correct wiring between motor contactor and L1, L2 and
L3 supply.
10 Is there voltage to T1, T2, and T3 of the motor contactor?
If yes, continue to next step.
Check for proper operation. Replace motor contactor if
necessary.
11 Is there voltage to L1, L2, and L3 of the motor?
If yes, continue to next step.
Correct wiring between motor contactor and motor.
12 Is the internal wiring of the motor correct for the supply
voltage?
Change the wiring accordingly.
13 Thermal overload cycled, allow motor to cool and recheck. Replace motor.
14 Unit operational.
- Drying Tumblers 1
- Table of Contents 2
- Section 4 –Grounding 3
- Section 5 –Service Procedures 3
- Section 6 –Adjustments 3
- Section 1 4
- Safety Information 4
- 4 M411429 5
- Section 2 6
- Introduction 6
- Customer Service 7
- Serial Plate Location 7
- Safety Warnings and Decals 8
- How A Tumbler Works 9
- Energy Saver Models 10
- Section 3 11
- Troubleshooting 11
- 12 M411429 12
- POSSIBLE CAUSE TO CORRECT 12
- 14 M411429 14
- 16 M411429 16
- 18 M411429 18
- 20 M411429 20
- 22 M411429 22
- Section 3 Troubleshooting 23
- 24 M411429 24
- 26 M411429 26
- 28 M411429 28
- Section 4 50
- Grounding 50
- Section 5 51
- Service Procedures 51
- 54 M411429 52
- Figure 1 52
- Figure 2 53
- 56 M411429 54
- Figure 3 54
- MANUAL TIMER 54
- Figure 4 55
- Figure 5 55
- 58 M411429 56
- Figure 6 56
- Figure 7 56
- Figure 8 57
- Figure 9 57
- 60 M411429 58
- Figure 10 58
- Figure 11 59
- 62 M411429 60
- Figure 12 60
- Figure 13 61
- 64 M411429 62
- Figure 14 63
- 66 M411429 64
- Section 5 Service Procedures 65
- 68 M411429 66
- Figure 15 66
- Figure 16 67
- ELECTRIC HEATER 67
- 70 M411429 68
- Figure 17 68
- Figure 18 69
- 72 M411429 70
- Figure 19 70
- Figure 20 70
- Figure 21 71
- ALTERNATE STYLEREGULAR STYLE 71
- 74 M411429 72
- Figure 22 72
- Figure 23 72
- NEWER MODELS OLDER MODELS 73
- 76 M411429 74
- Figure 25 74
- Figure 26 74
- Figure 27 75
- NEWER MODELS 76
- Figure 29 77
- 80 M411429 78
- Figure 30 78
- BELT/CHAIN NONREVERSING 78
- 82 M411429 80
- Figure 31 80
- Figure 32 81
- Figure 33 81
- 84 M411429 82
- Figure 34 82
- Figure 35 83
- 86 M411429 84
- Figure 36 84
- Figure 37 85
- 88 M411429 86
- Figure 38 87
- 90 M411429 88
- Figure 39 89
- REVERSING CONTROL ASSEMBLY 89
- Adjustments 90
- Section 6 90
- INSUFFICIENT 91
- NO AIRFLOW 91
- Section 6 Adjustments 92
- 96 M411429 93
- Figure 42 93
- Figure 43 94
- Figure 44 94
- 98 M411429 95
- BELT DRIVE 96
- BELT/BELT REVERSING 97
- REVERSING 99
- Figure 48 100
- BELT/CHAIN 101
- NONREVERSING 101
Related products and manuals for Electric laundry dryers ALLIANCE JT37CGI
(61 pages)
(172 pages)
(473 pages)
(44 pages)
(97 pages)© 2020, manymanuals.com. All rights reserved. | 0.204 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals