ALLIANCE JT37CGI Service Manual Page 79
- Page / 101
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
M411429 81
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumbler is properly grounded.
W002
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
IMPORTANT: Reversing Tumblers — Realign
motor pulley directly over sheave by loosening drive
motor mounting screws and repositioning motor on
mounting bracket.
104. DRIVE SPROCKET
Reversing Tumblers
a. Remove drive guard.
b. Loosen nut on idler housing attaching bolt and
slide idler housing to top of slotted mounting
holes in guide rails. This will provide slack in
drive chain for removal from sprockets. Refer
to Figure 31.
c. Remove chain.
d. Loosen setscrews holding drive sprocket to
idler shaft and pull sprocket free.
e. Remove key from shaft keyway.
f. Reinstall chain and drive guard.
IMPORTANT: Reassemble sprocket to idler shaft.
Align sprocket with cylinder sprocket. Make sure
shaft key is positioned under one of the sprocket
setscrews. Tighten setscrew over key first, then
tighten the other setscrew.
105. IDLER SHAFT
Refer to Figure 32.
a. Remove idler housing assembly.
b. Remove sheave and drive sprocket.
c. Remove bolt holding idler housing to guide
rails.
d. Support idler housing assembly and carefully
drive idler shaft from housing using a hammer
and a hardwood dowel.
e. Support idler housing assembly and remove
drive bearings from housing using a hammer
and a hardwood dowel.
f. Reinstall shaft and bearings.
IMPORTANT: When installing new bearings, apply
a film of oil to the bearing cavity surfaces of the
housing and the outside diameter of the bearings.
IMPORTANT: If a press is not available to install
bearings, tap bearings into housing using a prylin
hammer.
g. Reinstall chain guard.
NOTE: After installing sheave, adjust belt and then
adjust chain.
106. CYLINDER SPROCKET
Nonreversing Tumblers
Refer to Figure 30.
a. Remove drive guard.
b. Loosen jam nut on idler sprocket and move
sprocket to the right to relieve chain tension.
c. Run chain off idler sprocket and drive sprocket.
d. Lift chain off cylinder sprocket.
NOTE: After installing chain on drive and idler
sprockets, adjust chain.
e. Remove pal nut, jam nut, and sprocket from
cylinder shaft.
Reversing Tumblers
Refer to Figure 31.
a. Remove drive chain from sprocket.
b. Remove three attaching bolts from sprocket
hub.
c. Turn these three bolts into the threaded holes in
the sprocket hub, and “jack” the hub and
sprocket apart.
d. Remove hub, sprocket, key and spacer.
NOTE: After installing chain on drive and idler
sprockets, adjust chain.
- Drying Tumblers 1
- Table of Contents 2
- Section 4 –Grounding 3
- Section 5 –Service Procedures 3
- Section 6 –Adjustments 3
- Section 1 4
- Safety Information 4
- 4 M411429 5
- Section 2 6
- Introduction 6
- Customer Service 7
- Serial Plate Location 7
- Safety Warnings and Decals 8
- How A Tumbler Works 9
- Energy Saver Models 10
- Section 3 11
- Troubleshooting 11
- 12 M411429 12
- POSSIBLE CAUSE TO CORRECT 12
- 14 M411429 14
- 16 M411429 16
- 18 M411429 18
- 20 M411429 20
- 22 M411429 22
- Section 3 Troubleshooting 23
- 24 M411429 24
- 26 M411429 26
- 28 M411429 28
- Section 4 50
- Grounding 50
- Section 5 51
- Service Procedures 51
- 54 M411429 52
- Figure 1 52
- Figure 2 53
- 56 M411429 54
- Figure 3 54
- MANUAL TIMER 54
- Figure 4 55
- Figure 5 55
- 58 M411429 56
- Figure 6 56
- Figure 7 56
- Figure 8 57
- Figure 9 57
- 60 M411429 58
- Figure 10 58
- Figure 11 59
- 62 M411429 60
- Figure 12 60
- Figure 13 61
- 64 M411429 62
- Figure 14 63
- 66 M411429 64
- Section 5 Service Procedures 65
- 68 M411429 66
- Figure 15 66
- Figure 16 67
- ELECTRIC HEATER 67
- 70 M411429 68
- Figure 17 68
- Figure 18 69
- 72 M411429 70
- Figure 19 70
- Figure 20 70
- Figure 21 71
- ALTERNATE STYLEREGULAR STYLE 71
- 74 M411429 72
- Figure 22 72
- Figure 23 72
- NEWER MODELS OLDER MODELS 73
- 76 M411429 74
- Figure 25 74
- Figure 26 74
- Figure 27 75
- NEWER MODELS 76
- Figure 29 77
- 80 M411429 78
- Figure 30 78
- BELT/CHAIN NONREVERSING 78
- 82 M411429 80
- Figure 31 80
- Figure 32 81
- Figure 33 81
- 84 M411429 82
- Figure 34 82
- Figure 35 83
- 86 M411429 84
- Figure 36 84
- Figure 37 85
- 88 M411429 86
- Figure 38 87
- 90 M411429 88
- Figure 39 89
- REVERSING CONTROL ASSEMBLY 89
- Adjustments 90
- Section 6 90
- INSUFFICIENT 91
- NO AIRFLOW 91
- Section 6 Adjustments 92
- 96 M411429 93
- Figure 42 93
- Figure 43 94
- Figure 44 94
- 98 M411429 95
- BELT DRIVE 96
- BELT/BELT REVERSING 97
- REVERSING 99
- Figure 48 100
- BELT/CHAIN 101
- NONREVERSING 101
Related products and manuals for Electric laundry dryers ALLIANCE JT37CGI
(61 pages)
(172 pages)
(473 pages)
(44 pages)
(97 pages)© 2020, manymanuals.com. All rights reserved. | 2.276 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals